Discover Best Tips For Reloading PWC Trailers at Boat Ramps…

reloading pwc trailers

Photo © by Craig Nicholson

No Sea Doo ride is over without reloading your jet skis on your PWC trailer at the boat ramp where you launched safely earlier in the day. Properly securing your Sea Doo, jet ski or waverunner personal watercraft back on its trailer makes for safer towing home. It also enables easier launching next time for experienced riders, beginners or renters.

Reloading PWC Trailers – Before Backing Into the Water

With your tow vehicle in 4-wheel drive (if you have it), back down the boat ramp. If the launch is wide enough for more than one vehicle at a time, for courtesy’s sake pick a side and don’t hog the centre. Before backing into the water, check to make sure the electrical plug between trailer and tow vehicle is undone (should have happened at launch time) and that bunks are clear and properly positioned. Also, flip the lever on the trailer winch from the lock position to allow the winch strap(s) to be pulled out freely.

Reloading PWC Trailers – Position Trailer Bunks

reloading pwc trailers

Photo © by Allan Glanfield for Ontario Tourism

With carpeted bunks, back in until they are submerged because wetting them makes jet ski loading easier. But only back in as far as you can without submerging the rear tire bearings or axles of your tow vehicle – and leave it running throughout the entire reloading process so that water doesn’t flow into the exhaust pipe.

Then pull forward until the bunks are half out of the water because if they are in any deeper, the personal watercraft may float off them during loading. This is especially important if you are loading alone and have to get off the PWC to secure its front – relieved of your weight, it might float out of position.

With the trailer in place ready to be loaded, line up the jet ski centred on a set of bunks and drive on slowly until you’re sure the bow is properly aligned, then use the throttle to give it enough gas to seat it forward in the bunk. As soon as the personal watercraft is far enough forward, turn it off.

Reloading PWC Trailers – Hook Jet Ski Up To Trailer

reloading pwc trailers

Photo © by Craig Nicholson

If there’s only one person available to reload, this is where you have to get off the personal watercraft to hook the front up to the trailer. If you have an additional person at the trailer, the operator can stay in place aboard the jet ski.

The person doing the trailer hook up should pull out the winch strap far enough to reach the metal eye on the PWC bow. The winch strap should go between the two metal sides that the roller is mounted to, and under the roller to hold the strap in place between the metal sides during towing.

I place the strap loop through the eye on the PWC bow and then put the strap hook through the loop, ensuring that the safety snap on the hook is fully closed. Once hooked up, crank the winch handle to pull the jet ski as far forward as possible, preferably tight to the roller. Then flip the winch lever closed to lock it against the winch teeth. If the ramp is very steep and you can’t pull the watercraft fully forward, get it up as far as possible, lock the winch and complete the positioning of the PWC on the trailer after it’s out of the water and on level ground.

Reloading PWC Trailers – Easy Does It

reloading pwc trailers

Photo © by Allan Glanfield for Ontario Tourism

Pull the reloaded trailer out of the water and up the ramp slowly. Going slow will enable you to watch your load carefully to ensure that your personal watercraft are properly seated and secured. It will also help ensure that you don’t break a trailer tire seal if a tire happens to forcefully hitting a submerged ramp edge or other obstacle on the pull out. If you want to drain your personal watercraft and there’s no line up for the ramp, loosen the drain plugs while the back of the trailer is out of the water but angled down the ramp.

Reloading PWC Trailers – Final Steps

reloading pwc trailers

Photo © by Craig Nicholson

For the final reloading steps, drive slowly clear of the ramp to an area where you’re not in anyone’s way. At this time you need to…

  • Tie down the rear of the personal watercraft to the trailer.
  • Replug the trailer’s electrical hook up into your tow vehicle.
  • Remove all gear that doesn’t need to stay in your jet ski while it’s parked awaiting your next ride.
  • Clean off the outer surfaces of the jet ski.
  • Do a complete visual check over, looking for anything out of the ordinary that needs attention before your next ride.
  • Cover the watercraft and make sure the cover is properly secured to it won’t blow off or tear in transit.
  • Take your tow vehicle out of 4-wheel drive.

One final tip: Since your PWC’s may shift or settle slightly from the motion of starting to tow, it’s always a good idea to stop and check that your tie downs are still tight after trailering for 10 or 15 minutes. This is also a good opportunity to do a quick double check, walk around inspection just to make sure everything looks okay to continue trailering. If so, you’re good to go – and ready to launch for your next Sea Doo tour!

Check out my favourite Sea-Doo rides!

If you enjoyed this post, check out my other riding tips.

The tips and advice in this article are the opinions of the author, may not work in every situation and are intended only for the convenience and interest of the reader, who has the personal responsibility to confirm the validity, accuracy and relevancy of this information prior to putting it to their own use.

Like This Post? Follow Me on Facebook!